Acrease MR55B Rough Cut Mower

Kunz Engineering offers three different models of AcrEase pull behind rough cut mowers. The 57" rough cut tow behind mower models are great all around mowers that are capable of tackling heavy brush and tall grass, field or pasture mowing, food plots, or just as a trail cutter. These heavy duty brush cutters come in several different engine sizes and blade engagement clutch methods. The AcrEase rough cut models offer the highest horsepower and widest cut on the market for pull behind ATV and utility vehicle mowers.

• Pull the AcrEase Rough Cut Mower directly behind, off the left, or right side.
• The AcrEase Rough Cut Mowers use the ATV Tongue which is simple to install and remove. Quickly attach and remove with the provided farm style clevis pin.
• The AcrEase Rough Cut Mower comes standard with a manual clutch for blade engagement. An optional electric clutch model is also available.
• The AcrEase Rough Cut Mower comes standard with a 2 crank infinite (between 2"-8") height adjust system. An optional electric lift kit is also available.
• The AcrEase Rough Cut Mower is equipped with a large 3-3/4 gal. gas tank. This size tank allows for over 3 hours of mowing time.
• The AcrEase Rough Cut Mower is even electric start and has the battery box in the rear for safety.

• Class Mower: Rough Cut (Rear Discharge)
• Engine Make: Briggs & Stratton
• Engine Model: Intek AVS
• Engine HP: 17.5
• Lubrication Method: Splash
• Electric Start (Battery not included): Yes
• Number of Mower Blades: 2-30"
• Blade Tip Speed (ft/min): 19,000
• Cutting Width: 57"
• Cutting Height: 2.0" - 8.0" By Two Cranks
• Hitch: Directly Behind to Full Offset
• Blade Engagement Clutch: Manual
• Deck Metal Thickness: 10 GA
• Deck Top Plate Thickness: Two Separate 1/4" Thick Plates
• Weight: 550 lbs
• Pneumatic Fixed Rear Tire: Yes (15/600x6 4 ply tubeless with precision sealed bearings)
• Pneumatic Front Tires on Casters: Yes (5.30/4.50x6 tubeless with precision sealed bearings)
• Fuel Tank Size: 3-3/4 Gal.
• Blade: Spindles
• Greasable: Yes
• Shaft Size: 30mm
• Bearing #: 6206-2RST
• Drive Method: 1 B Section "V" Belt
• 1 Year Warranty: Non-Commercial

• Heavy deep deck design.
• Wide high capacity rear discharge.
• Heavy duty relube blade spindles with 30mm (1-3/16") shafts.
• 5/8" deck thickness in blade spindle location.
• 3/16" thick steel sides with 1/4" thick steel skids.
• Safety zone in front and rear of deck with rubber safety flap up front
• 2-30" blades, 5/16" thick.

• Click here to see the wetlands kit owner’s manual!
• Great for wetlands or marshy areas that stay wet all year around
• Works well in combination with small personal amphibious vehicles
• Kit more than doubles the tire surface area in contact with the ground
• Easy to install
• Works on all existing and new rough cut mowers
• The rough cut mower will not float with the wetlands kit installed.
• Water greater than 2-3" in depth should be avoided.
• With the Wetlands Kit installed the minimum cutting height is 3.5"-4".

• Click here to see the electric lift owner’s manual!
• Great for constantly changing terrain and grass/brush heights
• Allows for quick cutting height changes on the go from the seat of the tow vehicle
• Raise up and over rocks and logs with ease
• Heavy duty 1200 lb linear screw actuator made by Bear Linear
• Works on all existing and new rough cut mowers

• Click here to see the flotation kit owner’s manual!
• Great for mowing around ponds and on rough uneven ground where scalping would normally occur
• Clamping style receiver allows for adjustments from side to side with both the front and rear tires
• Pinned receivers make for quick kit removal when not needed
• Works on all existing and new rough cut mowers

Price includes shipping anywhere in the continental 48 USA
*This products ships via truck freight.